Engine hatch supports
Engine hatch supports
Greetings!
I'm new to the forum. I bought a 2008 220 two years back, it had just over 200 hours and was very well maintained. My question is my engine hatch will not stay up and I believe it is possible to be cut in half if it falls on you-very heavy. I found a chat with owners of an '05 with the same problem, they found 70lb Taylor Made replacements. Would these work for my boat or is there a difference between 05 and 08?
Thanks,
I'm new to the forum. I bought a 2008 220 two years back, it had just over 200 hours and was very well maintained. My question is my engine hatch will not stay up and I believe it is possible to be cut in half if it falls on you-very heavy. I found a chat with owners of an '05 with the same problem, they found 70lb Taylor Made replacements. Would these work for my boat or is there a difference between 05 and 08?
Thanks,
- Big Block Power
- Fleet Admiral
- Posts: 17910
- Joined: Sat May 07, 2016 8:05 pm
- Location: Neenah,Wi
- Contact:
Re: Engine hatch supports
I'm sure they are all the same. I would even go a bit higher. That cover weighs a ton. I hate lifting mine every 2 minutes to show the bad boy off. If it was only blue
03Cobalt220 8.1gxi DP
"Kids in Tow2"
"Pot The Jus" Originator :-)
Neenah Wi
#ItsBu'sfault
#FARCON Marine CC Core!
"Kids in Tow2"
"Pot The Jus" Originator :-)
Neenah Wi
#ItsBu'sfault
#FARCON Marine CC Core!
Re: Engine hatch supports
.GAH111 wrote: ↑Mon Aug 12, 2019 2:57 pm Greetings!
I'm new to the forum. I bought a 2008 220 two years back, it had just over 200 hours and was very well maintained. My question is my engine hatch will not stay up and I believe it is possible to be cut in half if it falls on you-very heavy. I found a chat with owners of an '05 with the same problem, they found 70lb Taylor Made replacements. Would these work for my boat or is there a difference between 05 and 08?
Thanks,
Hello Gah111. Welcome to the Cobaltchat forum. So glad you found us!
You should be able to replace those. Look on the side and see if you can find a make and model number of the gas compression spring. Then google that. Amazon is also another great source.
I just replaced my anchor locker gas spring today. It was made by Attwood. After googling the model number stamped on the side I found it was a 15” extended and 9.5” compressed with a 40 pound compression force.
I happened to check AutoZone and they had quite a selection. I actually found something similar that worked great.
Yours is a lot bigger but the same principles should apply.
Any pictures?
Again, welcome aboard mate!
.
You do not have the required permissions to view the files attached to this post.
2002 Cobalt 262
&
2005 Cobalt 263
496 MagHO
(sold )
Erie, PA
Currently boatless (for now)
will fly for food
(CChat moderator)
&
2005 Cobalt 263
496 MagHO
(sold )
Erie, PA
Currently boatless (for now)
will fly for food
(CChat moderator)
- Big Block Power
- Fleet Admiral
- Posts: 17910
- Joined: Sat May 07, 2016 8:05 pm
- Location: Neenah,Wi
- Contact:
Re: Engine hatch supports
Here's your numbers. They're also a thread on these I think in the 10 series.
You do not have the required permissions to view the files attached to this post.
03Cobalt220 8.1gxi DP
"Kids in Tow2"
"Pot The Jus" Originator :-)
Neenah Wi
#ItsBu'sfault
#FARCON Marine CC Core!
"Kids in Tow2"
"Pot The Jus" Originator :-)
Neenah Wi
#ItsBu'sfault
#FARCON Marine CC Core!
Re: Engine hatch supports
and thanks for getting with me so quickly.
You do not have the required permissions to view the files attached to this post.
- Big Block Power
- Fleet Admiral
- Posts: 17910
- Joined: Sat May 07, 2016 8:05 pm
- Location: Neenah,Wi
- Contact:
Re: Engine hatch supports
Yea they are model sl25 at 130#
Holy crap. I hope it goes up real easy. Does it even stay down. Lol
Are they that weak. I wanted to go stronger but that's way stronger.
Holy crap. I hope it goes up real easy. Does it even stay down. Lol
Are they that weak. I wanted to go stronger but that's way stronger.
03Cobalt220 8.1gxi DP
"Kids in Tow2"
"Pot The Jus" Originator :-)
Neenah Wi
#ItsBu'sfault
#FARCON Marine CC Core!
"Kids in Tow2"
"Pot The Jus" Originator :-)
Neenah Wi
#ItsBu'sfault
#FARCON Marine CC Core!
Re: Engine hatch supports
I need to check my posts more often, I see this response was a while back. In fact the hatch won't stay up on it's own with two of these compression springs. I'm thinking I need to go with a lesser spring load, 70lbs seems to be a consensus. There are two holding up the hatch. If anyone has any reason that I need 130 lbs let me know, I would think the hatch wouldn't stay closed.
G.H.
G.H.
- Big Block Power
- Fleet Admiral
- Posts: 17910
- Joined: Sat May 07, 2016 8:05 pm
- Location: Neenah,Wi
- Contact:
Re: Engine hatch supports
Correct. You don't want the hatch flying up while you're going down the hwy. But sure that it would but.
I am not going with 70 when I do mine. Maybe a 90. That lid is a tank.
I am not going with 70 when I do mine. Maybe a 90. That lid is a tank.
03Cobalt220 8.1gxi DP
"Kids in Tow2"
"Pot The Jus" Originator :-)
Neenah Wi
#ItsBu'sfault
#FARCON Marine CC Core!
"Kids in Tow2"
"Pot The Jus" Originator :-)
Neenah Wi
#ItsBu'sfault
#FARCON Marine CC Core!
Re: Engine hatch supports
I finally got someone that knows the application and could help me with correct compression spring replacement. I contacted a seller on Ebay and gave him the application and what was on the boat currently. He did not have it but suggested I contact Attwood (maker of SpringLift). I was on perpetual hold, left a voice mail that was never returned. I also contacted Iboats via email, one of the retailers Attwood had listed, the rep got back to me in a day saying that they did not have the specific part but gave me a link to LiftSupportsDepot.com who did have a replacement (not an Attwood part). the replacements are on the way. Interestingly, the site said to orient the shaft in a down position so oil will be in contact with the piston when closed. Good information. Also, it is a 130 # spring lift.
- Big Block Power
- Fleet Admiral
- Posts: 17910
- Joined: Sat May 07, 2016 8:05 pm
- Location: Neenah,Wi
- Contact:
Re: Engine hatch supports
Well let us know how it works for you.
03Cobalt220 8.1gxi DP
"Kids in Tow2"
"Pot The Jus" Originator :-)
Neenah Wi
#ItsBu'sfault
#FARCON Marine CC Core!
"Kids in Tow2"
"Pot The Jus" Originator :-)
Neenah Wi
#ItsBu'sfault
#FARCON Marine CC Core!
Re: Engine hatch supports
Got good feedback on this. Our boat is on Grand Lake in Oklahoma, I'm in Kansas so it took a while before I got things sorted out. The lift supports were the correct ones, 130 lbs and all. It was a quick easy on and off installation so I can recommend LiftSupportsDepot.
G.H.
G.H.
- Big Block Power
- Fleet Admiral
- Posts: 17910
- Joined: Sat May 07, 2016 8:05 pm
- Location: Neenah,Wi
- Contact:
Re: Engine hatch supports
Thanks how easy is it now to lift the hatch.
03Cobalt220 8.1gxi DP
"Kids in Tow2"
"Pot The Jus" Originator :-)
Neenah Wi
#ItsBu'sfault
#FARCON Marine CC Core!
"Kids in Tow2"
"Pot The Jus" Originator :-)
Neenah Wi
#ItsBu'sfault
#FARCON Marine CC Core!
Re: Engine hatch supports
GAH, Grand Lake is an awesome lake, been awhile since I've been on it and cant wait to visit it again.
Re: Engine hatch supports
Hey there td...
Let’s get you to the new members section so we can hear about Grand Lake more. ( we know it’s Packys playground)
Plus we Loce pics!
2008 272 , 496 HO fo SHO
California Delta
Table Rock Lake
#FARCON
California Delta
Table Rock Lake
#FARCON
Re: Engine hatch supports
.
Agreed! and welcome aboard TD!
.
You do not have the required permissions to view the files attached to this post.
2002 Cobalt 262
&
2005 Cobalt 263
496 MagHO
(sold )
Erie, PA
Currently boatless (for now)
will fly for food
(CChat moderator)
&
2005 Cobalt 263
496 MagHO
(sold )
Erie, PA
Currently boatless (for now)
will fly for food
(CChat moderator)
Who is online
Users browsing this forum: No registered users and 1 guest